« previous next »
Pages: 1   Go Down

Author Topic: new engine rebuild table  (Read 1119 times)

0 Members and 2 Guests are viewing this topic.

Offline steptoe

  • Administrator
  • Hero Member
  • *****
  • Posts: 2170
  • Gender: Male
  • Geoff,, a XS addict,, Bundy QLD
    • Bikes and trucks what more could you want
Re: new engine rebuild table
« Reply #9 on: July 20, 2016, 04:32:24 PM »
Ev came over one day {thanks again mate} and the whole area has had a redesign and fit out,, miles more room
Logged

Offline Jonesy :-)

  • Hero Member
  • *****
  • Posts: 1735
Re: new engine rebuild table
« Reply #8 on: July 20, 2016, 04:11:33 PM »
you must have had the hospital orderlys in to do a clean up of the ward, from my dim memory I didnt think you could get to that back wall where the operating table is now........I could be wrong as I may have had a few sedatives at the time ;)
Logged
78 E Stock
78 E Stockish with spoked wheels
80 G spoked wheels and other subtle mods
81 RH problem child. Gone & forgotten
97 TRX 850
94 Yam 350 Big Bear 4 wheeler
?? Yam TTR 125 with milk crate. (RIP the Posty)

Offline steptoe

  • Administrator
  • Hero Member
  • *****
  • Posts: 2170
  • Gender: Male
  • Geoff,, a XS addict,, Bundy QLD
    • Bikes and trucks what more could you want
Re: new engine rebuild table
« Reply #7 on: July 20, 2016, 01:12:03 PM »
got the swinging light on the other bench Tim
Logged

Offline Tim

  • Hero Member
  • *****
  • Posts: 384
Re: new engine rebuild table
« Reply #6 on: July 17, 2016, 05:29:26 PM »
masterful Steptoe
all it really needs to finish the look is a lighting rig that swings over the bench
ohhh and the machine that goes ping :)
Logged
former xs  owner  but still has an itch

Offline steptoe

  • Administrator
  • Hero Member
  • *****
  • Posts: 2170
  • Gender: Male
  • Geoff,, a XS addict,, Bundy QLD
    • Bikes and trucks what more could you want
Re: new engine rebuild table
« Reply #5 on: July 17, 2016, 08:54:50 AM »
apart from the draws needing to be finished with sides and compartments and layering, the big stuff,s done.
thought I,d throw another spare bit on the other side, just because it was there and I had a spare couple of hinges.
this is it in situ


and this is all tucked up asleep
Logged

Offline yama80

  • Newbie
  • *
  • Posts: 1
  • Gender: Male
  • Welcome to XS1100 Australia. Now let us know a bit about you in General Discussions and email me your postal details so I can send you our group stickers etc.
Re: new engine rebuild table
« Reply #4 on: July 16, 2016, 12:39:16 PM »
Good old Aussie engineering Geoff.Kudos 8)
Logged

Offline XSIIE

  • Hero Member
  • *****
  • Posts: 963
  • Gender: Male
  • Welcome to the group. Now let us know a bit about you in General Discussions and email me your postal details so I can send you our group stickers etc.
Re: new engine rebuild table
« Reply #3 on: July 16, 2016, 07:22:29 AM »
Homage maistro
Logged
"If we do what we always do then
we will never be more than we are"
Poh (Kungfoo Panda).
78E x 2
78E DJP Chair
80G (current project)
81H
81RH x 4
82P x 2

Offline Jonesy :-)

  • Hero Member
  • *****
  • Posts: 1735
Re: new engine rebuild table
« Reply #2 on: July 15, 2016, 09:57:49 PM »
Nice work, maybe you can sell the pattern to ikea.
 will you be wearing those disposable sanitary booties on those bare feet when the hospital reaches full operating status
Logged
78 E Stock
78 E Stockish with spoked wheels
80 G spoked wheels and other subtle mods
81 RH problem child. Gone & forgotten
97 TRX 850
94 Yam 350 Big Bear 4 wheeler
?? Yam TTR 125 with milk crate. (RIP the Posty)

Offline steptoe

  • Administrator
  • Hero Member
  • *****
  • Posts: 2170
  • Gender: Male
  • Geoff,, a XS addict,, Bundy QLD
    • Bikes and trucks what more could you want
new engine rebuild table
« Reply #1 on: July 15, 2016, 08:29:41 PM »
here at the barefoot garage we,re getting closer to surgery status, with the almost complete rebuild table,
I started with a 1200mm x 1200mm yellow tongue floor board on a set of legs and have built on that


we then hinged another large piece to the side


then I cut some support out riggers


then trimmed and cut the long bit off so it will fold into itself

now to finish off with a few sliding draws and it,ll be ready for some work

note all the table has folded on itself taking up no room at all



Logged
Pages: 1   Go Up
« previous next »